manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 117 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 117

Regulatory Statements

● 

BSMI statement (Taiwan)..............................................................................................117

● 

Canadian requirements.................................................................................................117

● 

CE Statement................................................................................................................117

● 

China ROHS................................................................................................................. 118

● 

FCC warning (US only)................................................................................................. 118

● 

KCC statement (Republic of Korea)..............................................................................118

● 

VCCI statement.............................................................................................................118

● 

Germany....................................................................................................................... 119

BSMI statement (Taiwan)

Warning:

This is Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

Canadian requirements

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations, ICES-003 Class A.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

CE Statement

ATTENTION

This is a Class A product. In a domestic environment, this product might cause radio interference, and
the user might be required to take corrective measures.

The standards compliance label on this device contains the CE mark which indicates that this system
conforms to the provisions of the following European Council directives, laws, and standards:

• Electromagnetic Compatibility (EMC) Directive 2004/108/EEC
• Low Voltage Directive (LVD) 2006/95/EC
• EN50082-2/EN55024:1998 (European Immunity Requirements)

Brocade VDX 6940 Hardware Installation Guide

117

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments