manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 42 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 42

Installation procedure for flush-front mounting

NOTE

The switch must be turned off and disconnected from the fabric during this procedure.

NOTE

The illustrations in this document show a 1U switch, but the instructions are the same for a 2U switch.

Complete these tasks to install the switch in a four-post rack:

•

Attaching the front brackets

 on page 42

•

Attaching the extension brackets to the switch

 on page 43

•

Installing the switch in the rack

 on page 44

•

Attaching the rear brackets to the extensions

 on page 45

•

Attaching the rear brackets to the rack posts

 on page 46

Attaching the front brackets

Complete the following steps to attach the front brackets to the switch.

1. Position the right front bracket with the flat side against the right side of the switch at the front of the

switch, as shown in 

Figure 19 

.

2. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and

then into the holes on the side of the switch. Use the upper and lower screw holes, leaving the
center holes empty.

3. Repeat step 1 and step 2 to attach the left front bracket to the left side of the switch.
4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

Installation procedure for flush-front mounting

42

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments