manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 25 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 25

1

Fan #1

2

Fan #2

3

Fan #3

4

Fan #4

5

Fan #5

6

Power supply #1

7

Power supply #2

8

Handle

9

Airflow label

10 DC wire connectors
11 Status LED
12 Captive screws
13 Airflow label
14 Fan captive screw
15 Status LED
16 Handle
17 Ground lug attachment screws

FIGURE 7

 Non-port-side view showing DC power supplies

Non-port-side view of VDX 6940-144S

The following illustration shows the fan assemblies, AC power supplies, and other components on the
non-port side of the Brocade VDX 6940-144S. Refer to 

LED locations

 on page 73 for details on LED

locations.

1

Ground lug attachment screws

2

Fan #1

3

Fan #2

4

Fan #3

5

Fan #4

6

AC power supply #1

7

AC power supply #2

FIGURE 8

 Non-port-side view showing AC power supplies

The following illustration shows more detail of the AC power supplies and fans.

Non-port-side view of VDX 6940-144S

Brocade VDX 6940 Hardware Installation Guide

25

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments