manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 108 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 108

LEDs

System component

Description

Switch status and
management

One bicolor system status LED (green and amber) on the port side.

One green power status LED on the port side.

Two green Ethernet management port status LEDs on the port side.

Port activity 40-GbE ports

One green LED per port for 40-GbE operation.

Four green LEDs per port for 10-GbE operation in breakout mode (Brocade VDX
6940-36Q).

Port activity fixed 10-GbE
ports (Brocade VDX
6940-144S)

One bicolor LED (green and amber) per port to indicate status on the port side.

Fan status

One bicolor LED (green and amber) per fan to indicate status on nonport side.

Power supply status

Brocade VDX 6940-36Q - One green LED per power supply to indicate status on
nonport side.

Brocade VDX 6940-144SOne green LED to indicate status of input voltage and one
bi-color (green/amber) LED to indicate status of output voltage.

Other

System component

Description

Serial cable

Rollover cable

RJ-45 connectors (2)

One serial port used for console.

Brocade VDX 6940-36Q - One RJ-45 10/100/1000 Mbps Ethernet out-of-band
management port

Brocade VDX 6940-144S - One RJ-45 1000 Mbps Ethernet out-of-band
management port

USB connector

Used for data and firmware downloads

Weight and physical dimensions

Fully loaded

 means that all FRUs and transceivers are installed.

Brocade VDX 6940 Switch Technical Specifications

108

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments