manualshive.com logo in svg

Baroness LM2700, Service Manual

Share
Download
Baroness LM2700 Service Manual Download Page 48

Disconnect the oil pressure switch wire and
the starter wire.

1

2

o3sknc-047

Removal of Engine_008

1

Oil pressure switch wire

2

Starter  wire

Caution

Use fuel hose plugs with no dirt or dust
attached.

Remove the two fuel hoses and install a
screw cap to them.

1

2

o3sknc-048

Removal of Engine_009

1

Fuel hose (main)

2

Fuel hose (return)

Follow the steps below to remove the air
cleaner hose and abrasion-resistant hose.

Loosen the hose band, and then remove
the air cleaner hose from the engine.

10.

11.

12.

[1]

Loosen the hose band, and then remove
the abrasion-resistant hose from the air
cleaner.

3

1

2

1

5

4

o3sknc-049

Removal of Engine_010

1

Hose band

2

Air cleaner hose

3

Abrasion-resistant hose

4

Engine

5

Air cleaner

Follow the steps below to remove the air
cleaner.

Remove the bolts and spring washers
from the frame, and then remove the air
cleaner.

4

2

1

1

2

3

o3sknc-050

Removal of Engine_011

1

Bolt

2

Spring washer

3

Frame

4

Air cleaner

[2]

13.

[1]

LM2700

Engine

Page 4-20

Removal and installation of each section

Summary of Contents for LM2700






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands