manualshive.com logo in svg

Baroness LM2700, Service Manual

Share
Download
Baroness LM2700 Service Manual Download Page 182

Solenoid Specifications

Rated
Voltage

DC 12 V

Rated
Current

1.5 A

Discharge
Quantity

400 cc/min

Tank Unit

The tank unit is located at the top of the fuel
tank and connected to the fuel gauge. And it
converts the amount of rise and fall of the float
installed in the fuel tank to a resistance value,
which is used to compute the remaining amount
of fuel.

1

2

y1ynmg-002

Tank Unit_001

1

Tank unit

2

Float

Rotation Sensor (Electromagnetic Pickup)

The rotation sensor (electromagnetic pickup) is
located in the engine flywheel area and it
detects the rpm by means of the flywheel ring
gear and sends the signal to the tachometer
which displays the rpm.

1

qsth91-001

Rotation Sensor (Electromagnetic Pickup)_001

1

Rotation sensor

LM2700

Electrical system

Page 6-34

Electrical components

Summary of Contents for LM2700






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands