Baroness LM2700 Service Manual Download Page 320

Page: 320 / 325

MANUAL

㧱

404

1. DESCRIPTION

The RT parking brake assembly is a ball and ramp, sliding caliper brake designed for use

primarily as a parking brake, with some secondary braking capability. The brake has an

open caliper design to facilitate changing linings, along with a retraction spring to reduce

parasitic drag. It is sealed from the environment to provide a long and trouble free service

life.

2. PARTS

LIST

5dm3ww-010

RT mechanical brake manual_003

LM2700

Reference

Page 10-14

RT mechanical brake manual

Summary of Contents for LM2700






































































































































































































































































































































Search results

Summary of Contents for LM2700

Reviews:

Related manuals for LM2700

Brands by name

Popular brands

Baroness LM2700, Service Manual

Search results

Summary of Contents for LM2700

Reviews:

Related manuals for LM2700

Brands by name

Popular brands