54
4.3
MCT Startup Wizard - fine-tuning
In the previous section, the motor response was ‘coarse tuned’. The following sections describe how to
fine tune the motor response. If you are familiar with closed loop servo control theory then you may
wish to proceed straight to section 4.3.2. If not, the following section provides an introduction to the
various factors involved, with simple analogies shown with [
italics
].
4.3.1
An introduction to closed loop control
When a demand is made to move the axis position, the MintDrive control software translates this into
motor currents. An encoder or resolver is used to measure the motor position, and every 1ms
*
the
MintDrive compares the demanded and measured positions and calculates the demand needed for the
motor to minimize the difference, the
following error
.
This system of constant measurement and correction is known as closed loop control.
[
For the analogy, imagine you are in your car waiting at an intersection. You are going to go straight on
when the lights change, just like the car standing next to you which is called
Demand
. You’re not going
to race
Demand
though - your job as the controller (MintDrive) is to stay exactly level with
Demand,
looking out of the window to measure your position
].
The main term that the MintDrive uses to correct the error is called
Proportional gain
(
KPROP
).
A very simple proportional controller would simply multiply the amount of error by the Proportional gain
and apply the result to the motor [
the further
Demand
gets ahead or behind you, the more you press or
release the gas pedal
].
If the Proportional gain is set too high overshoot will occur, resulting in the motor vibrating back and
forth around the desired position before it settles [
you press the gas pedal so hard you go right past
Demand.
To try and stay level you ease off the gas, but end up falling behind a little. You keep
repeating this and after a few tries you end up level with
Demand,
travelling at a steady speed. This is
what you wanted to do but it has taken you a long time
].
If the Proportional gain is increased still further, the system becomes unstable [
you keep pressing and
then letting off the gas pedal so hard you never travel at a steady speed
].
To reduce the onset of instability, a term called
Velocity Feedback gain
(
KVEL
) is used. This resists
rapid movement of the motor and allows the Proportional gain to be set higher before vibration starts.
Another term called
Derivative gain
(
KDERIV
) can also be used to give a similar effect.
With Proportional gain and Velocity Feedback gain (or Derivative gain) it is possible for a motor to come
to a stop with a small following error [ Demand
stopped so you stopped too, but not quite level
].
The MintDrive tries to correct the error, but because the error is so small the amount of torque
demanded might not be enough to overcome friction.
This problem is overcome by using a term called
Integral gain
(
KINT
). This sums the error over time,
so that the motor torque is gradually increased until the positional error is reduced to zero [
like a person
gradually pushing harder and harder on your car until they’ve pushed it level with
Demand].
However, if there is large load on the motor (it is supporting a heavy suspended weight for example), it
is possible for the output to increase to 100% demand. This effect can be limited using the
KINTLIMIT
keyword which limits the effect of KINT to a given percentage of the demand output. Another keyword
called
KINTMODE
can even turn off integral action when it’s not needed.
The final term to consider is
Velocity Feed forward
(
KVELFF
) which can be used to increase the
response and reduce the following error, especially with velocity controlled servos.
Summary of Contents for MintDrive
