AUMA ACV 01.2 Manual Download Page 14 | Manualshive

Page: 14 / 168

background image

→

Set selector switch to position Remote control (REMOTE).

➥

Now, the actuator can be remote-controlled via fieldbus.

Information

For actuators equipped with a positioner, it is possible to change over between OPEN
- CLOSE control (Remote OPEN-CLOSE) and setpoint control (Remote SET-
POINT). For further information, refer to chapter <Change-over between OPEN -
CLOSE control and setpoint control>.

Information

For actuators equipped with a positioner, it is possible to change over between OPEN
- CLOSE control (Remote OPEN-CLOSE) and setpoint control (Remote SET-
POINT). For further information, please refer to the Manual (Operation and setting).

3.3.

Menu navigation via push buttons (for settings and indications)

Menu navigation for display and setting is made via the push buttons [1 – 4] of the
local controls.

Set the selector switch [5] to position 0 (OFF) when navigating through the menu.

The bottom row of the display [6] serves as navigation support and explains which
push buttons [1 – 4] are used for menu navigation.

Figure 2:

[1–4] Push buttons or navigation support

[5]

Selector switch

[6]

Display

Table 1: Important push button functions for menu navigation

Functions

Navigation sup-
port on display

Push buttons

Change screen/selection

Up ▲

[1]

Change values

Enter figures from 0 to 9

Change screen/selection

Down ▼

[2]

Change values

Enter figures from 0 to 9

14

Actuator controls

Operation

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
12
13
14
15
16
...
»

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Related manuals for ACV 01.2

Brand: Garmin Pages: 12

Brand: Tapeswitch Pages: 13

Brand: Accu-Sort Pages: 22

Brand: Gardena Pages: 17

Brand: SAFI Pages: 18

Brand: Badger Meter Pages: 2

Brand: Badger Meter Pages: 48

BadgerTouch HREBT

Brand: Badger Meter Pages: 12

Brand: Badger Meter Pages: 16

Brand: Omegalink Pages: 2

Brand: N-Com Pages: 20

Brand: N-Com Pages: 28

Brand: IBM Pages: 20

Brand: DAV TECH Pages: 24

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 16

Brand: Klimaire Pages: 5

AMES 4000SS Series

Brand: Watts Pages: 8

Brand: Audioaccess Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands