AUMA ACV 01.2 Manual Download

Page: 74 / 168

Remote

Stepping mode is active in the operation modes:

Remote

Remote II

Fieldbus

Local

Stepping mode is active in the operation modes:

Local

Service

Remote and local

Stepping mode is active in the operation modes:

Remote

Remote II

Fieldbus

Local

Service

Information

The timer cannot be by-passed in <Operation mode EMERGENCY>.

8.8.3.

Start and end of stepping mode

Start and end of stepping mode can be individually set for both directions.

Customer settings M0041

Timer M0142

End stepping CLOSE M0152
Start stepping CLOSE M0153
Start stepping OPEN M0154
End stepping OPEN M0155

Default values:

End stepping CLOSE

0.0 %

Start stepping CLOSE

100.0 %

Start stepping OPEN

0.0 %

End stepping OPEN

100.0 %

Setting ranges:

End stepping CLOSE

0.0 – 99.9 %

Start stepping CLOSE

0.1 – 100.0 %

Start stepping OPEN

0.0 – 99.9 %

End stepping OPEN

0.1 – 100.0 %

8.8.4.

On times and off times

On or off times can be set individually for directions OPEN and CLOSE.

Customer settings M0041

Timer M0142

On time CLOSE M0163
Off time CLOSE M0164
On time OPEN M0165
Off time OPEN M0166

Default values:

00:05.0 min : s

(= 5 seconds; for all on and off times)

Setting ranges:

00:01.0 ... 00:05.00.0 min : s

(= 1 second up to 30 minutes; for all

on and off times)

8.9.

Profibus DP interface

8.9.1.

Bus address (slave address)

The bus address can be entered manually via push buttons at the local controls
according to the description below. For information on how to set the bus address
via fieldbus, refer to Manual Device integration Profibus DP.

Customer settings M0041

Profibus DP M0016

DP1 slave address M0098
DP2 slave address M0295

Default value:

126

Setting range:

0 ... 126

Information

Parameter

DP2 slave address

is only available for some redundancy options.

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands