AUMA ACV 01.2 Manual Download

Page: 50 / 168

According to the present description, two digital inputs have to be configured as
control signals to allow for external speed selection.

Required user level:

Specialist (4)

Device configuration M0053

I/O interface M0139

Digital inputs M0116

Example

Use inputs DIN 5 and DIN 6 as control signals for external speed selection:

Parameter:

Signal DIN 5 M0122

Speed int. sel. bit 0

Parameter:

Signal DIN 6 M0123

Speed int. sel. bit 1

Table 9:

Output speed

Input signals (DIN) for external speed selection

Speed int. sel. bit 1

Speed int. sel. bit 0

Speed internal1

Speed internal2

Speed internal3

Speed internal 4

0 = low level (0 V DC or input open)
1 = high level (standard: +24 V DC)

Speed value for coding both digital inputs with “high active”

Information

The logic for the digital inputs may be inverted. Depending on the parameter setting
(e.g.

Coding DIN 6 M0128

), the input is either

High active

Low active

. Default

setting is

High active

Configuration of analogue input for speed

For setting of parameter

Sp. source...

Analogue input

An analogue input (AIN 1 or AIN 2) has to be configured as described to be able to
use an external (analogue) speed setpoint.

Required user level:

Specialist (4)

Device configuration M0053

I/O interface M0139

Analogue inputs M0389

Signal AIN 1 M0135
Signal AIN 2 M0138

Example

Use analogue input AIN 1 for speed setpoint:

Parameter

Signal AIN 1 M0135

Interface speed

Information

The speed range for the analogue input is determined via parameters

Speed rem.

min. M1936

and

Speed rem. max M1937

8.1.2.

Speed for constant (internal) speed setpoint: set

For setting of parameter

Sp. source...

(internal speed setpoint)

●

Sp. source...

Internal 1

Internal 2

Internal 3

Internal 4

●

Sp. source...

2 DigIn: "Internal (1-4)"

If the actuator is controlled via an external speed source, the internal speed values
described here will not have an impact on the operation behaviour.

Customer settings M0041

Speed functions M1699

Speed internal1 M1930
Speed internal2 M1931
Speed internal3 M1932

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands