AUMA ACV 01.2 Manual Download

Page: 13 / 168

Operation

3.1.

Operating the actuator from local controls

Local actuator operation is performed using the local controls push buttons of actuator
controls.

Figure 1: Local controls

[1]

Push button for operation command in direction OPEN

[2]

Push button STOP

[3]

Push button for operation command in direction CLOSE

[4]

Push button RESET

[5]

Selector switch

Hot surfaces, e.g. possibly caused by high ambient temperatures or strong
direct sunlight!

Risk of burns

→

Verify surface temperature and wear protective gloves.

→

Set selector switch [5] to position Local control (LOCAL).

➥

The actuator can now be operated using the push buttons [1 – 3]:

Run actuator in direction OPEN: Press push button [1]

Stop actuator: Press push button STOP [2].

Run actuator in direction CLOSE: Press push button [3]

Information

The OPEN and CLOSE operation commands can be given either in push-to-run or
in self-retaining operation mode. For further information, please refer to <Push-to-
run operation or self-retaining local> chapter.

3.2.

Actuator operation from remote

Risk of immediate actuator operation when switching on!

Risk of personal injuries or damage to the valve

→

If the actuator starts unexpectedly: Immediately turn selector switch to 0 (OFF).

→

Check input signals and functions.

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Operation

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands