AUMA ACV 01.2 Manual Download

Page: 130 / 168

●

Signal state at input:
-

DIN 4: Not active (triangle not filled in)
Low level = 0 V = No operation command in direction OPEN

DIN 5: Active (triangle is black)
Low level = 0 V = EMERGENCY operation command is available

Diagnostic of digital outputs

For the digital outputs (DOUT), both coding and signal states are indicated at the
output by means of symbols.

Table 20: Symbol explanation

State output (output contact)

Signal (indication)

Code

Symbol

Low = 0 (output contact not operated)

Not active

High active

High = 1 (output contact operated)

Active

High active

High = 1 (output contact operated)

Not active

Low active

Low = 0 (output contact not operated)

Active

Low active

Figure 58: Example of DOUT 1 and DOUT 2

●

Configuration:
-

DOUT 1: Indication: Fault has occurred.

DOUT 2: Indication: End position CLOSED reached

●

Coding:
-

DOUT 1:

Low active

(Triangle pointing in downward direction)

DOUT 2:

High active

(Triangle pointing in upward direction)

●

Signal state at output:
-

DOUT 1: Not active (triangle not filled in)
High level = +24 V DC = no indication (no fault available)

DOUT 2: Active (triangle is black)
High level = +24 V DC= indication (end position CLOSED reached)

14.4.

Position transmitter and potentiometer diagnostic

Menu is only visible if the actuator is equipped with a potentiometer.

Required user level:

Observer (1)

or higher.

Diagnostics M0022

Position transm. potent. M0831

The following states can be checked via diagnostic:

Signification

Menu ID

Parameters

Low limit Uspan

M0832

Low limit Uspan

Volt.level diff. potent.

M0833

Volt.level diff. potent.

Raw val. pos. OPEN

M0999

Raw val. pos. OPEN

Raw val. pos. CLOSED

M1001

Raw val. pos. CLOSED

Potent. raw value /mV

M1005

Potent. raw value /mV

14.5.

Diagnostic Position transmitter RWG

Menu is only visible if the actuator is equipped with electronic position transmitter
(RWG).

Required user level:

Observer (1)

or higher.

130

Actuator controls

Diagnostics

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands