AUMA ACV 01.2 Manual Download Page 122

Page: 122 / 168

Self-retaining when leaving the factory in both direction (cw and ccw).

12.1.8.

Dead band

The dead band prevents operation to a new setpoint position within a specified band.

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

Dead band M1145

Default value:

0.00°

Setting range:

0.00 – 36.0°

(degrees)

12.1.9.

Correction of inertia

Due to reaction times and inertia, each Multiport valve has a specific inertia. This
can be compensated by inertia correction.

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

Overrun M1656

Default value:

0.00°

Setting range:

0.00° – 10.0°

(degrees)

12.1.10. Backlash compensation

Adjustable backlash compensation of the overall system including valve coupling.

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

Backlash comp. M1146

Default value:

0.00°

Setting range:

0.00 – 36.0°

(degrees)

12.1.11. Signalling behaviour of positions: set/check

Reaching of a point (valve port) can be signalled:

●

via bus (see separate instructions)

●

via indication lights (LEDs) of the local controls or
(refer to chapters <Indications> <Indication lights>)

●

via output contacts
(refer to chapters <Indications> <Assignment of outputs>)

Signal behaviour, this means the signal behaviour upon reaching a position, is set
via parameter

MPV sign. beh. 1

Customer settings M0041

Multiport valve M1140

MPV sign. beh. 1 M1147

Default value:

No signal

Setting values:

No signal

A: Signal behaviour Off. Position is not signalled.

C________|¯¯¯¯¯¯¯¯O

B: Signal is active from reaching the position up to 360°.

C¯¯¯¯¯¯¯¯¯|_______O

C: Signal is active from 0° until the position is reached.

C_______|¯|_______O

D: When passing the position, a pulse signal is issued. The pulse range (range +/–
around the pivot point) depends on the set hysteresis.

122

Actuator controls

Product variants

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands