AUMA ACV 01.2 Manual Download

Page: 111 / 168

Default values:

Detect. time dt

(for potentiometer/EWG/RWG within actuator) =

00:05.0 min:s

( 5

seconds)

Detect. time dt (MWG)

(for MWG within actuator) =

00:00.5 min:s

(0.5 seconds)

Setting ranges:

Detect. time dt

00:01.0 ... 30:00.0 min:s

(minutes:seconds)

Detect. time dt (MWG)

00:00.1 ... 00:02.0 min:s

(minutes:seconds)

10.6.3.

Travel difference dx

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Motion detector M0676

Travel diff. dx M0678
Travel diff. dx (MWG) M0679

Default values:

Travel diff. dx

(for potentiometer/EWG/RWG within actuator) =

1.0 %

Travel diff. dx (MWG)

(for MWG within actuator) =

(increments)

Setting ranges:

Travel diff. dx

1.0 ... 10.0 %

Travel diff. dx (MWG)

2 ... 20

(increments)

10.6.4.

Delay time

Delay time of the signal:

Handwheel oper.

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Motion detector M0676

Delay time M0764

Default value:

6.000 s

(seconds)

Setting range:

0.001 ... 65.535 s

10.7.

Monitoring of electronics power supply

Actuator controls monitor the following voltages and signal a warning (refer to <Fault
signals and warnings> chapter):

●

Auxiliary voltage 24 V DC, e.g for supplying the control inputs

●

Voltage 24 V AC for controlling the reversing contactors, for thermoswitches
and heater within the actuator and for generating the 115 V AC auxiliary voltage
for the customer (option)

●

Internal 24 V DC power supply of the electronics components (within the actu-
ator controls and in the actuator)

●

External 24 V DC supply of the electronics (option)

Activate monitoring of auxiliary voltage 24 V DC

Required user level:

Specialist (4)

Device configuration M0053

Monitoring function M0645

Monitor 24 V DC cust. M0650

Default value:

Function not active

Setting values:

Function not active

Monitoring is deactivated.

111

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Monitoring functions

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands