background image

Setting range:

1 ... 1,024

 [kByte]

With the maximum setting range of 1,024 kbyte, at least 20,000 events can be stored.

Information

Some events are stored in a sector which cannot be overwritten. This includes, for
example, modifications of the parameter setting, enabling of functions and certain
special functions.

Number of events in the buffer

The events are first stored into an internal RAM. From this buffer, they are written
to the event report after the set report cycle. The number of events in the buffer can
be set here.

Information

In case of power failure, the events in the buffer will be lost.

Required user level:

AUMA (6)

.

Asset Management M1231

Event report M0195

Buffer size M0332

Default value:

50

 [events]

Setting range:

10 ... 100

 [events]

Save interval

The event report is updated and saved at a defined cycle. This cycle (save interval)
can be reduced or extended

Required user level:

AUMA (6)

.

Asset Management M1231

Event report M0195

Save interval M0331

Default value:

50,000

Setting range:

1,000 ... 65,535

 [ms]

15.3.

Characteristics

15.3.1.

Torque-travel characteristic

Conditions

Electric actuators with electronic control unit

Actuator controls (non-intrusive version) from firmware version 02.03.01

Properties

Representation of torque requirement across complete travel (resolution of 0.1 %)
During each travel, actuator controls continuously record the torques applied.

Application

When comparing two characteristics (current characteristic with archived
characteristic), the wear within the valve or the actuator can be assessed.

Display torque-travel characteristics

Asset Management M1231

Characteristics M0313

Torque-travel M1229

Characteristics M0546

3 characteristics with two diagrams each (direction OPEN and direction CLOSE) are
displayed while the arrow indicates the operation direction diagram.

Each characteristic has a designation (e.g.

_REF 1_

), which can be changed.

Use push buttons 

Up ▲Down ▼

 to change between characteristics.

136

 Actuator controls

Asset Management

 ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Reviews: