AUMA ACV 01.2 Manual Download

Page: 6 / 168

9.6.4.

Interlock behaviour (running direction)

9.7.

Local Stop

9.7.1.

Behaviour

9.8.

EMERGENCY stop function

9.9.

Partial Valve Stroke Test (PVST)

9.9.1.

PVST activation

9.9.2.

PVST source: set

100

9.9.3.

Operation mode for PVST

100

9.9.4.

Behaviour for PVST: define

100

9.9.5.

Partial stroke for PVST: set

100

9.9.6.

PVST monitoring time: set

101

9.9.7.

PVST operating time: set

101

9.9.8.

PVST reversing time: set

101

9.9.9.

PVST reminder

101

9.9.10.

Speed for PVST: set

102

9.10.

Bluetooth interface can be activated and deactivated

105

10.

Monitoring functions .............................................................................................................

105

10.1.

Torque monitoring

105

10.1.1.

Torque by-pass

106

10.1.2.

Torque limitation of torque by-pass

107

10.2.

Motor protection monitoring (thermal monitoring)

107

10.3.

Type of duty monitoring (motor starts and running time)

109

10.4.

Operating time monitoring

109

10.5.

Reaction monitoring

110

10.6.

Motion detector

110

10.6.1.

Activate motion detector

110

10.6.2.

Detection time dt

111

10.6.3.

Travel difference dx

111

10.6.4.

Delay time

111

10.7.

Monitoring of electronics power supply

112

10.8.

Temperature monitoring

112

10.9.

Heater system/heater monitoring

113

10.10.

Verification of sub-assemblies

113

10.11.

Phase failure monitoring

115

11.

Functions: activate and enable.............................................................................................

115

11.1.

Functions: activate

115

11.2.

Functions: enable

117

12.

Product variants.....................................................................................................................

117

12.1.

Multiport valve

117

12.1.1.

Actuator type: set/check

117

12.1.2.

Gear reduction ratio: set/check

118

12.1.3.

Number of ports (positions)

118

12.1.4.

Home port (zero position): set

119

12.1.5.

Positions (of valve ports): define/check

119

12.1.6.

Operate to position via push buttons of the local controls

121

12.1.7.

Operate to position from Remote

122

12.1.8.

Dead band

122

12.1.9.

Correction of inertia

122

12.1.10.

Backlash compensation

Actuator controls

Table of contents

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands