AUMA ACV 01.2 Manual Download

Page: 139 / 168

Characteristics M0313

Interval position-time M0805

Default value:

[s]

Setting values:

1 ... 3600

[s]

15.3.3.

Temperature-time characteristic

Properties

Up to four temperature-time characteristics can be recorded unless the devices are
fitted with suitable sensors.

Conditions

●

For recording the temperature within the control unit:
MWG (magnetic limit and torque transmitter)

●

For recording the temperature within the motor:
additionally temperature sensor (PT 100) in the motor

●

For recording the temperature within the gear housing:
additionally temperature sensor (PT 100) in the gearing

Application

Evaluation of the temperature-time characteristics allows to gain knowledge about
the service conditions (ambient temperatures) of the actuator.

Display temperature-time characteristic

Asset Management M1231

Characteristics M0313

Temperature-time M0714

Up to four characteristics are shown in the display.

CONTROLS TEMPERATURE

= temperature within the control unit

MWG TEMPERATURE

= MWG temperature

MOTOR TEMPERATURE

= temperature within the motor

GEAR TEMPERATURE

= within the gear housing

Use push buttons

Up ▲Down ▼

to change between available characteristics.

Figure 61: Example of temperature-time (within the control unit)

- - -

0° line

Recording interrupted e.g. due to power failure

The actuator controls display shows temperature evolution during one week. AUMA
CDT software reads out the evolution during an entire year.

The following further information is saved with the characteristic (can be requested
via push button

Details

)

●

Saving date:

Time of last temperature measurement

●

Starting date:

Time of first temperature measurement

●

Scaling:

Y-axis (temperature)

●

Min. value:

Minimum measured value

●

Max. value:

Maximum measured value

15.4.

Histograms

15.4.1.

Motor running time-position (histogram)

Conditions

●

Actuators of the type range SA 07.2 – SA 16.2/SAR 07.2 – SAR 16.2

139

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Asset Management

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands