manualshive.com logo in svg

AUMA ACV 01.2, Manual

Share
Download
AUMA ACV 01.2 Manual Download Page 75

8.9.2.

Redundancy

Redundancy can be entered manually via the push buttons at the local controls
according to the description below.

Device configuration M0053

Profibus M0799

Redundancy M0601

Default value:

None

Setting values:

None

No redundancy

DP-V2 (SR)

DP-V2 (system redundancy)

DP-V2 (FR)

DP-V2 (flying redundancy)

AUMA redundancy I

Redundant line topology with universal redundancy behaviour according to AUMA
redundancy type I

AUMA redundancy II

Redundant line topology with universal redundancy behaviour according to AUMA
redundancy type II

Information

For detailed information on redundancy types, refer to Manual Device integration
Profibus.

8.9.3.

Response telegrams for AUMA redundancy II

When using AUMA redundancy II, response telegrams can be sent on both channels.

Device configuration M0053

Profibus M0600

Behaviour TxM0801

Default value:

Tx active channel

Setting values:

Tx active channel

Response telegrams are only sent via the active channel.

Tx both channels

Response telegrams are sent via both channels, the active and the passive channel.

8.9.4.

Connection type – compatibility with process representation

Process representation compatibility is to be exclusively guaranteed. User parameters,
other parameters as well as timely behaviour of the application are not guaranteed.
This means that replacing actuator controls with another type of actuator controls
will have a certain impact on the DCS.

Device configuration M0053

Profibus M0799

Connection type M01640

Default value:

AUMATIC .2

Setting values:

AUMATIC .2

Process representation is compatible with AC 01.2 actuator controls.

AUMATIC .1

Process representation is compatible with AC 01.1 actuator controls.

AM/VM 0...1000 ‰

Process representation is compatible with AM 01.1 actuator controls (target/actual
position of 0 ...1,000 per mil)

AM/VM 0...100 %

Process representation is compatible with AM 01.1 actuator controls (target/actual
position of 0 ...100 percent)

75

Actuator controls 
ACV 01.2/ACVExC 01.2 Profibus DP 

Application functions

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands