AUMA ACV 01.2 Manual Download Page 41

Page: 41 / 168

Confirm new end posi-

tion

10. Press

Yes

to confirm new end position.

➥

Display indicates:

End pos. CLOSED set!

➥

The left LED is illuminated (standard version) and thus indicates that the end

position CLOSED setting is complete.

11. Make selection:

→

Edit →

back to step 9: Set end position CLOSED "once again"

→

Esc →

back to step 4; either set end position OPEN or exit the menu.

Set end position OPEN

CMD0010

12. Re-set end position OPEN:

12.1 For large strokes: Set selector switch in position Local control (LOCAL)

and operate actuator in motor operation via push button

(OPEN) in

direction of the end position.
Information: Stop actuator before reaching end of travel (press STOP
push button to avoid damage.

12.2 Engage manual operation.

12.3 Turn handwheel until valve is open.

12.4 Turn back the handwheel by an amount equal to the overrun.

12.5 Set selector switch to position 0 (OFF).

➥

Display indicates:

Set end pos. OPEN? Yes No

Confirm new end posi-

tion

13. Press

Yes

to confirm new end position.

➥

Display indicates:

End pos. OPEN set!

➥

The right LED is illuminated (standard version) and thus indicates that the end

position OPEN setting is complete.

14. Make selection:

→

Edit →

back to step 12: Set end position OPEN "once again"

→

Esc →

back to step 4; either set end position CLOSED or exit the menu.

Information

If an end position cannot be set: Check the type of control unit in actuator.

7.3.2.

End position setting via stroke

For all applications not allowing to operate the valve during commissioning,
the second end position can be set via the stroke.

→

The basics are the MWG incremental values shown in this chapter.

→

The first end position either OPEN or CLOSED, depending on the valve position
during commissioning, can be set as usual using the limit switching. For this,
refer to

page 39, Limit switching: set

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Basic settings for commissioning

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands