manualshive.com logo in svg

AUMA ACV 01.2, Manual

Share
Download
AUMA ACV 01.2 Manual Download Page 128

14.

Diagnostics

Diagnostics comprise information on the device and on device sub-assemblies for
support during commissioning, maintenance or corrective action.

14.1.

Electronic device ID

The electronic device ID provides information about the order data (important for
enquiries with the factory).

Device ID M0021

Identification M0026
Version M0062

Information on device identifications can be modified with the appropriate rights (user
level).

Table 17: Information on device identifications

Identification M0026

User level re-
quired for modi-
fication

Description

Indication on display

Service (5)

Device designation of the actuator
controls

Device designation M0072

Specialist (4)

Device ID for identification within
the plant marking (e.g. KKS
(Power Plant Classification Sys-
tem)

Device tag M0072

Specialist (4)

Project name of the plant

Project name M0068

Menu with information regarding identification of the
actuator controls

Actuator controls M0028

Service (5)

Order number of the actuator
controls

Order no. controls M0055

Service (5)

Serial number of the actuator
controls

Serial no. controls M0056

Service (5)

Wiring diagram number of the ac-
tuator controls

Wiring diagram M0059

Service (5)

Date of manufacture of controls

Date of manufacture M0063

Menu with information regarding identification of the
actuator

Actuator M0029

Service (5)

Order number of the actuator

Order no. actuator M0057

Service (5)

Serial number of the actuator

Serial no. actuator M0220

Service (5)

Wiring diagram number of the ac-
tuator

Wiring diag. actuator M0060

Table 18: Information on device version

Version M0062

Description

Indication on display

Firmware version

Firmware M0077

Language version

Language M0565

Menu with further items for requesting the current image
file versions of current sub-assemblies (only visible for
user level 

AUMA (6)

)

Details Firmware M0515

Menu with further items for requesting the hardware
article number of the actual sub-assemblies (only visible
for user level 

AUMA (6)

)

Hardware art. no. M0684

14.2.

Bluetooth connection diagnostic

Menu is only visible if function 

Bluetooth M0573

 is activated.

Required user level:

Specialist (4)

 or higher.

128

 Actuator controls

Diagnostics

 ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands