AUMA ACV 01.2 Manual Download Page 88 | Manualshive

Page: 88 / 168

background image

●

Input

EMERGENCY

= high level (standard: +24 V DC)

No EMERGENCY operation

9.3.1.

EMERGENCY behaviour: activate

Required user level:

Specialist (4)

or higher.

Device configuration M0053

Application functions M0178

Activation M0212

EMCY behaviour M0589

Default value:

Function not active

Setting values:

Function not active

Function <EMERGENCY behaviour> deactivated.

Function active

Function <EMERGENCY behaviour> activated.

For activated EMERGENCY behaviour:

Risk of actuator operation due to an EMERGENCY signal!

Risk of personal injuries or damage to the valve.

→

For commissioning and maintenance work: Set selector switch to position 0
(OFF). Motor operation can only be interrupted in this selector switch position.

→

If the actuator starts unexpectedly: Immediately turn selector switch to position
0 (OFF).

Information

EMERGENCY behaviour must be completely configured during first activation. This
means the setting of the following parameters must be adapted to the required actu-
ator behaviour in particular:

EMCY fail.reac. EMCY source EMCY operation mode

EMCY operation EMCY position

9.3.2.

EMERGENCY failure reaction

Required user level:

Specialist (4)

or higher.

Customer settings M0041

EMCY behaviour M0198

EMCY fail.reac. M0203

Default value:

Good signal first

Setting values:

Good signal first

The <EMERGENCY behaviour> is initiated as soon as the EMERGENCY signal
changes from high to low. Example: for binary EMERGENCY input of +24 V DC to
0 V. This prevents the <EMERGENCY behaviour> from being initiated immediately
once the actuator controls are switched on and no EMERGENCY signal is present.

Immediately active

The <EMERGENCY behaviour> is initiated by a low level at the EMERGENCY signal.
For this setting, the EMERGENCY signal has to have a high level before switching
on the actuator controls; otherwise <EMERGENCY behaviour> is initiated immediately
after switching on.

For the setting

Immediately active

:

The actuator can start immediately when switching on!

Risk of personal injuries or damage to the valve.

→

Ensure that the EMERGENCY signal is present when switching on.

→

Should the actuator start unexpectedly: Immediately set selector switch to pos-
ition 0 (OFF).

88

Actuator controls

Failure functions

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
86
87
88
89
90
...
»

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Related manuals for ACV 01.2

Brand: ABB Pages: 30

Brand: ABB Pages: 15

Brand: ABB Pages: 10

Brand: ABB Pages: 44

Brand: Harrington Pages: 8

Brand: Acclaim Lighting Pages: 32

Brand: Unitech Pages: 11

Brand: B meters Pages: 10

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands