AUMA ACV 01.2 Manual Download

Page: 96 / 168

Information

The logic for the digital inputs may be inverted. Depending on the parameter setting
(e.g.

Coding DIN 5 M0127

), the input is either

High active

Low active

. Default

setting is

High active

Enable/disable commands via digital input

Switching- behaviour for coding

High active

●

Input

Enable OPEN

= low level (0 V DC or input open):

Operation command enabled.

●

Input or

Enable OPEN

= high level (default: +24 V DC):

Operation command disabled,

9.6.1.

Interlock: activate

Required user level:

Specialist (4)

or higher.

Device configuration M0053

Application functions M0178

Activation M0212

Interlock M0663

Default value:

Function not active

Setting values:

Function not active

Function <Interlock (enable operation commands)> deactivated.

Function active

Function <Interlock (enable operation commands)> activated.

9.6.2.

Source of Interlock enable signal: set

Customer settings M0041

Interlock M0664

Interlock source M1013

Default value:

Active comm. source

Setting values:

Active comm. source

Signals for enabling operation commands are sent via the active interface. I.e.
changing the command source also changes the failure source of the enable signal.

Interface

The enable signal for the operation commands must be configured as binary signal
(default: +24 V DC) at a digital input (parameter:

Enable OPEN

Enable CLOSE

Fieldbus

The enable signal for the operation commands must be triggered by the fieldbus
commands

Interlock OPEN

Interlock CLOSE

9.6.3.

Operation mode for interlock

The additional enable signal can be activated for different operation modes.

Customer settings M0041

Interlock M0664

Oper. mode Interlock M0665

Default value:

Off

both directions

Setting values:

Off

Interlock is off.

Remote

Interlock is active in operation modes:

RemoteRemote II Fieldbus

Local

Interlock is active in operation modes:

Local

Service

Remote and local

Interlock is active in operation modes:

Remote

Remote II

Fieldbus

Local

Service

9.6.4.

Interlock behaviour (running direction)

The Interlock behaviour determines which selector switch functions (LOCAL, OFF)
require an additional enable signal.

Actuator controls

Failure functions

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands