manualshive.com logo in svg

AUMA ACV 01.2, Manual

Share
Download
AUMA ACV 01.2 Manual Download Page 24

Figure 25: Function check

For further information, please also refer to <Corrective action>.

Maintenance required (S0010)

The 

S0010

 indication shows maintenance indications according to NAMUR

recommendation NE 107.

If such an indication has occurred, the display shows 

S0010

:

●

the number of indications occurred

●

a blinking square with an oilcan after approx. 3 seconds

Figure 26: Maintenance required

For further information, please also refer to <Corrective action>.

Failure (S0011)

The 

S0011

 indication shows the causes of the failure indication according to NAMUR

recommendation NE 107.

If such an indication has occurred, the display shows 

S0011

:

●

the number of indications occurred

●

a blinking circle with a cross after approx. 3 seconds

Figure 27: Failure

For further information, please also refer to <Corrective action>.

24

 Actuator controls

Indications

 ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands