AUMA ACV 01.2 Manual Download Page 118

Page: 118 / 168

Setting values:

Table 16: Selection of gearboxes supported by AUMA

Sizes GS160.3 – GS 250.3

Sizes GS 50.3 – GS 125.3

GS160.3

GS50.3

GS160.3/GZ160.3(4:1)

GS63.3

GS160.3/GZ160.3(8:1)

GS80.3

GS200.3

GS100.3

GS200.3/GZ200.3(4:1)

GS100.3/VZ2.3

GS200.3/GZ200.3(8:1)

GS100.3/VZ3.3

GS250.3

GS100.3/VZ4.3

GS250.3/GZ250.3(4:1)

GS125.3

GS250.3/GZ250.3(8:1)

GS125.3/VZ2.3

GS125.3/VZ3.3

GS125.3/VZ4.3

12.1.3.

Number of ports (positions)

Number of valve ports (positions)

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

Number of ports M1141

Default value:

Setting ranges:

In operation mode Remote

In operation mode Local or Fieldbus

12.1.4.

Home port (zero position): set

The home port is the zero position (0° or 360° of one turn) and is consequently the
starting point for all other intermediate positions.

Information

Set the gear reduction ratio (parameter

Reduction ratio M1143

) and the actuator

type (parameter

Actuator type M1142

) prior to setting the home port.

Set home port

Position multiport valve to zero position either via manual operation (handweel)
or via motor operation (via push buttons of local controls)

In a next step, confirm this position (with

Yes

) as homeport via parameter

MPV

home port M1162

As an alternative, the home port position can also be confirmed via a signal at
a digital input. To this end, a digital input has to be available and configured.

Set home port (zero position) via parameter

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

MPV home port M1162

Set?

Successful homeport setting is visualised by a black circle on the actuator controls
display: .

Reset homeport (zero point)

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

118

Actuator controls

Product variants

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands