AUMA ACV 01.2 Manual Download Page 59 | Manualshive

Page: 59 / 168

background image

8.4.1.

Operation profile: activate

Required user level:

Specialist (4)

or higher.

Device configuration M0053

Application functions M0178

Activation M0212

Operation profile M0294

Default value:

Function not active

Setting values:

Function not active

Function <Operation profile> deactivated.

Function active

Function <Operation profile> activated.

8.4.2.

Operation profile for intermediate positions (pivot points): set

When reaching an intermediate position, the operation behaviour of the actuator
may be set.

Customer settings M0041

Intermediate positions M0143

Operation behaviour M0257

Operation behaviour 1 M0258

Default value:

Off

Setting values:

Off

No intermediate stop, actuator continues the operation.

Stop in OPEN

●

Actuator stops at pivot point during operation in direction OPEN.

●

The operation command has to be cleared by means of the STOP command
and a new operation command has to be sent to resume operation.

●

This function is not active in operation mode Remote SETPOINT.

Stop in CLOSED

●

Actuator stops at pivot point during operation in direction CLOSE.

●

The operation command has to be cleared by means of the STOP command
and a new operation command has to be sent to resume operation.

●

This function is not active in operation mode Remote SETPOINT.

Stop in OPEN & CL.

●

Actuator stops automatically upon reaching the pivot point.

●

The operation command has to be cleared by means of the STOP command
and a new operation command has to be sent to resume operation.

●

This function is not active in operation mode Remote SETPOINT.

Off time in OPEN

Actuator stops at pivot point during operation in direction OPEN. If an operation
command in direction OPEN is present at the end of the pause time, the actuator
resumes operation into direction OPEN. If an operation command in direction CLOSE
is present during the pause time, the pause is aborted and operation into direction
CLOSE resumed.

Off time in CLOSED

When reaching the pivot point, the actuator stops during operation in direction CLOSE.
If an operation command in direction CLOSE is present at the end of the pause time,
the actuator resumes operation into direction CLOSE. If an operation command in
direction OPEN is present during the pause time, the pause is interrupted and
operation into direction OPEN resumed.

Off time in OPEN & CL.

Actuator stops automatically upon reaching the pivot point. If an operation command
in direction OPEN or CLOSE is present at the end of the pause time, the actuator
resumes operation depending on the operation command.

Information

The actuator stops for each activated intermediate position for which operation be-
haviour

Stop in OPEN

,

Stop in CLOSED

or

Stop in OPEN & CL.

is assigned.

59

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Application functions

«
...
57
58
59
60
61
...
»

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Related manuals for ACV 01.2

Brand: FAAC Pages: 12

Brand: Eaton Pages: 86

UNIVERGE SL2100

Brand: NEC Pages: 196

UNIVERGE SL2100

Brand: NEC Pages: 174

ElectraElite IPK

Brand: NEC Pages: 151

Brand: CALEFFI Pages: 2

Brand: CALEFFI Pages: 12

Brand: Caliber Pages: 6

Brand: Gardigo Pages: 8

Brand: Gardigo Pages: 19

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Brand: Nedap Pages: 20

Brand: Wealden Rehab Pages: 29

Brand: Watts Pages: 4

Brand: National Instruments Pages: 78

Brand: M-system Pages: 21

Brand: Partizan Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands