AUMA ACV 01.2 Manual Download

Page: 40 / 168

Select main menu

Set selector switch to position 0 (OFF).

Press push button C and hold it down for approx. 3 seconds.

➥

Display goes to main menu and indicates:

▶ Display

Select parameter

Select parameter either:

→

click via the menu

to parameter, or

→

via direct display: press and enter ID

M0084

➥

Display indicates:

Set end pos.CLOSED?

CLOSED or OPEN

Select via

Up ▲ Down ▼

→

▶ Set end pos.CLOSED? M0084

→

▶ Set end pos. OPEN? M0085

➥

The black triangle

▶

indicates the current selection.

Press

➥

The display indicates either:

Set end pos.CLOSED? CMD0009 →

continue with step 9

Set end pos. OPEN? CMD0010 →

continue with step 12

Specialist (4) →

continue with step 6

User login

Use

Up ▲ Down ▼

to select user:

Information: Required user level:

Specialist (4)

or higher

➥

The symbols have the following meaning:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

Press

to confirm selected user.

➥

Display indicates:

Password 0***

Enter password (

→

enter password).

➥

The display indicates either:

Set end pos.CLOSED? CMD0009 →

continue with step 9

Set end pos. OPEN? CMD0010 →

continue with step 12

Set end position

CLOSED

CMD0009

Set end position CLOSED again :

9.1 For large strokes: Set selector switch in position Local control (LOCAL)

and operate actuator in motor operation via push button

(CLOSE) in

direction of the end position.
Information: Stop actuator before reaching end of travel (press STOP
push button to avoid damage.

9.2 Engage manual operation.

9.3 Turn handwheel until valve is closed.

9.4 Turn back the handwheel by an amount equal to the overrun.

9.5 Set selector switch to position 0 (OFF).

➥

Display indicates:

Set end pos.CLOSED? Yes No

Actuator controls

Basic settings for commissioning

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands