APRILIA RSV4 1100 Factory Service Station Manual Download Page 542 | Manualshive

Page: 542 / 549

background image

TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE.
THE LACK OF AN ADEQUATE BATTERY CHARGE BEFORE THE FIRST USE WILL CAUSE A
PREMATURE FAILURE OF THE BATTERY.

CAUTION

WHEN INSTALLING THE BATTERY, ATTACH THE POSITIVE LEAD FIRST AND THEN THE NEG-
ATIVE ONE, AND PERFORM THE REVERSE OPERATION DURING REMOVAL.

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THAT RECOMMENDED. THE USE OF A
FUSE OF UNSUITABLE CAPACITY MAY RESULT IN SERIOUS DAMAGES TO THE WHOLE VE-
HICLE OR EVEN CAUSE A FIRE.

- Check the battery charge by holding down the TEST button on the BATTERY CAPACITY INDICATOR

located between the terminals on the top of the battery.

If by pressing TEST, the BATTERY CAPACITY INDICATOR shows LOW (1 blue LED lit) or MEDIUM

(2 blue LED indicators lit), charge the battery.

RECHARGE

- Always use a specific charger for lithium batteries to recharge the battery.

- To avoid damage to the battery, the charging voltage must NEVER be higher than 15 volts.

- Do not charge the battery with a charger with automatic DESULPHATION MODE using a voltage

higher than 15 volts.

- Always remove the battery from the vehicle before connecting it to the charger.

- Stop charging if the battery feels warm to the touch. Allow the battery to cool before resuming charging.

- After recharging the battery, leave it to stand for 1 hour before pressing the TEST button on the

BATTERY CAPACITY INDICATOR. If the indicator shows LOW (1 blue LED lit) or MEDIUM (2 blue

LED indicators lit), the battery must be charged again.

CHARGE MODES

Normal recharge

- Electric current: 1,0 A

- Time: 4 hours

Quick charge

- Electric current: 10 A

- Time: 0,5 hours

CAUTION

THE RECHARGE CURRENT MUST NOT EXCEED 10A.

WARNINGS

- Do not knock, throw or subject the battery to violent shocks.

Pre-delivery

RSV4 1100 Factory

PRE DE - 542

«
...
540
541
542
543
544
...
»

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RSV4 1100 Factory

Brand: Zinc Pages: 24

Longtail Cargo Frame

Brand: Surly Pages: 4

Brand: Daymak Pages: 29

Brand: Cannondale Pages: 16

Brand: Green Light Cycle Pages: 24

Brand: Yeti Cycles Pages: 15

Brand: baby joy Pages: 11

Brand: SPIELWERK Pages: 11

REGULATOR Ti SEATPOST

Brand: SALSA Pages: 3

Brand: Vibe Pages: 17

Brand: Tilo Pages: 2

Brand: UFREE SCOOTER Pages: 13

Brand: GLOBBER Pages: 20

Brand: GLOBBER Pages: 74

303303/20190717TW012

Brand: APLIC Pages: 16

303508/20181218TW012

Brand: APLIC Pages: 32

Brand: HASE Bikes Pages: 60

Brand: CHAMPEDAL Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands