APRILIA RSV4 1100 Factory Service Station Manual Download Page 99

Page: 99 / 549

WIRING TABLE E2 - INSTRUMENT SUPPORT

ARCH AND FRONT PART

Position the main wiring harness and secure it to

the right hand instrument holder support using a

grey reference clamp

WIRING TABLE E3 - INSTRUMENT SUPPORT

ARCH AND FRONT PART

Using the second pre-installed clamp on the in-

strument support arch, group together all the ca-

bles from the left hand side of the handlebar, and

fasten them together, making a note of their re-

spective lengths first

WIRING TABLE E4 - INSTRUMENT SUPPORT

ARCH AND FRONT PART

Cable output on right hand side of the instrument

support

1. RH light switch wiring harness

WIRING TABLE E5 - INSTRUMENT SUPPORT

ARCH AND FRONT PART

Cable output on left hand side of the instrument

support

1. LH light switch wiring harness;

2. Clutch switch wiring harness;

3. Traction control commands wiring harness.

RSV4 1100 Factory

Electrical system

ELE SYS - 99

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands