APRILIA RSV4 1100 Factory Service Station Manual Download Page 495

Page: 495 / 549

•

Unscrew and remove the inner screw.

•

Remove the pump cover.

TO PREVENT IRREPARABLE DAMAGE TO THE PUMP,
UNSCREW AND REMOVE THE INNER SCREW BEFORE
REMOVING THE COVER.

•

At each removal, replace the inner gas-

ket between the pump casing and the

cover and the O ring on the pump cas-

ing.

ENSURE THAT THE LIQUID PASSAGE ORIFICES ARE
NOT OBSTRUCTED.

Removing the radiator

RADIATOR BRACKET REMOVAL

•

Operating from the right side of the mo-

torcycle, move the main cable harness

and remove the screw fixing the radia-

tor to the retainer bracket.

RSV4 1100 Factory

Cooling system

COOL SYS - 495

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands