APRILIA RSV4 1100 Factory Service Station Manual Download Page 414 | Manualshive

Page: 414 / 549

background image

SET SPRING PRE-LOADING AND SHOCK ABSORBER RE-
BOUND DAMPING ACCORDING TO THE VEHICLE USE
CONDITIONS.
IF THE SPRING PRE-LOADING IS INCREASED, IT IS NEC-
ESSARY TO INCREASE THE REBOUND DAMPING AC-
CORDINGLY TO AVOID SUDDEN JERKS WHEN RIDING.

CAUTION

ALWAYS OBSERVE THE RECOMMENDED ADJUSTMENT
RANGE.

CAUTION

FOR THE CORRECT SETTING PARAMETERS, READ THE
PARAGRAPH "SETTING THE REAR SHOCK ABSORBER"
CAREFULLY.
TAKE YOUR VEHICLE TO AN Authorised Aprilia Dealer, IF
NECESSARY.
TRY RIDING THE VEHICLE ON THE STREET UNTIL THE
OPTIMUM ADJUSTMENT IS OBTAINED.

Adjusting

SPORT SETTINGS MAY BE USED ONLY FOR OFFICIAL
COMPETITIONS TO BE CARRIED OUT ON TRACKS,
AWAY FROM NORMAL ROAD TRAFFIC AND WITH THE
AUTHORISATION OF THE RELEVANT AUTHORITIES.

STANDARD

ADJUSTMENT

(

FOR

ROAD

USE

)

Specification

Desc./Quantity

Shock absorber centre-to-centre distance (A)

311 mm (12.24 in)

(preloaded) Spring (B) length

148 mm (5.83 in)

Rebound adjustment, knob (1)

open (**) 12 clicks from fully closed (*)

Compression adjustment, knob (2)

open (**) 12 clicks from fully closed (*)

RACING

ADJUSTMENT

(

ONLY

TRACK

USE

)

Specification

Desc./Quantity

Shock absorber centre-to-centre distance (A)

311 mm (12.24 in)

(preloaded) Spring (B) length

146 mm (5.75 in)

Rebound adjustment, knob (1)

open (**) 12 clicks from fully closed (*)

Compression adjustment, knob (2)

open (**) 12 clicks from fully closed (*)

Suspensions

RSV4 1100 Factory

SUSP - 414

«
...
412
413
414
415
416
...
»

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RSV4 1100 Factory

Brand: oh!bike Pages: 20

Brand: Yuba Pages: 2

LittleONE LD-W-0144

Brand: Pepita Pages: 35

Brand: PARLEE Pages: 28

Brand: Scott Pages: 16

Brand: Specialized Pages: 35

Brand: Yedoo Pages: 96

Brand: Qualisports Pages: 5

T2 BIKE TRAILER

Brand: Allen Sports Pages: 12

Brand: DAHON Pages: 2

Brand: Tianjin Key-Disp Pages: 13

Brand: Hase Spezialräder Pages: 28

Brand: VDO Cyclecomputing Pages: 20

Brand: Tune Pages: 8

Brand: Tune Pages: 9

TURNSTANGE WUNDERBAR

Brand: Tune Pages: 16

Brand: Tune Pages: 10

RACE ATTACK SL-160 CARBON

Brand: Rose electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands