APRILIA RSV4 1100 Factory Service Station Manual Download Page 533

Page: 533 / 549

•

Uncouple from its support the connec-

tor (1) of the fuel pump and disconnect

it.

•

Disconnect the connector (2) of the in-

ertia platform.

•

Working on the left side, disconnect the

tank's two vent pipes.

•

Slightly lift the fuel tank and working on

the right side of the motorcycle, dis-

connect the fuel pipe at the coupling

point.

•

Remove the tank.

RSV4 1100 Factory

Bodywork

BODYW - 533

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands