APRILIA RSV4 1100 Factory Service Station Manual Download Page 368

Page: 368 / 549

The five ring gaps (two piston rings, two oil scraper

rings, one oil scraper spring) are fitted displaced

90º to each other, starting from the exhaust-side

stud bolt opposite the chain and continuing clock-

wise.

The fitted pistons have two selections A and B.

Therefore they are coupled with the cylinder ac-

cording to the selection of the latter, which is

marked on the upper crankcase halves.

Pre-assemble the pistons on the workbench with

the connecting rod shank and the relative semi-

bushing.

The pre-assembly procedure is identical for all four

pistons and must be done as follows:

•

with the piston crown parallel to the

workbench and the arrow (1) posi-

tioned from the side opposite of the

operator, fit the connecting rod shank

with the bevelling (2), on the hole of the

rod head, on the right side.

•

Position the special tool on the crank-

case.

•

Partially insert the connecting rod

shank - piston assembly in the corre-

sponding cylinder with the arrow (on

the piston) twisted 45°towards the ex-

haust.

•

When the connecting rod head is low,

and has exceed its lubricating jet, ro-

tate the connecting rod shank - piston

assembly with the arrow on the piston

crown towards the exhaust; the bevel-

Engine

RSV4 1100 Factory

ENG - 368

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands