APRILIA RSV4 1100 Factory Service Station Manual Download Page 165 | Manualshive

Page: 165 / 549

background image

read by the control unit, but a recovery value is

displayed

Lambda correction

•

Example value with key ON: 0 %

•

Example value with engine on: -10% /

+10%

In closed loop, the value must be close to 1.00

(values not within the -15% / +15% interval indi-

cate a fault). In an open circuit, the lambda probe

signal is too low. Therefore, the control unit takes

it as a lean mixture condition and will try to enrich

it. The value read will be +25%: once this value is

reached and kept unchanged for a certain time, the

function diagnosis of the lambda probe is activated

with following deactivation of it.

This diagnosis is activated when the correction

constantly arrives -25%.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTIC TOOL: STATUSES

Lambda probe: Start-up_Lean_Rich_Fault due to rich titre_Fault due to lean air-fuel mixture

•

If the probe connector is disconnected (voltage almost equal to zero) it switches to the state

of Fault due to lean air-fuel mixture

Lambda check: Open loop/Closed loop/Rich in closed loop/Lean in closed loop/enriched

•

Closed loop indicates that the control unit is using the lambda probe signal to keep the

combustion is close as possible to the stoichiometric value.

DIAGNOSTIC TOOL: ACTIVATIONS

Lambda probe heater

•

The injection relay (No. 33 in the electrical circuit diagram, placed under the saddle next to

the battery positive, CHECK, however, the identification of the relay with the colour of the

cables) is energised and the heating circuit is closed to ground 5 times (pin 3 of the Lambda

probe connector). Electrical continuity is required in the wiring for the relay to activate cor-

rectly: no errors are generated in case of no activation.

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

P0150 Front bank lambda probe

Electrical diagnosis:

RSV4 1100 Factory

Electrical system

ELE SYS - 165

«
...
163
164
165
166
167
...
»

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RSV4 1100 Factory

JUNIOR LOW RIDER

Brand: TRAILMATE Pages: 7

Brand: Momentum Pages: 84

Brand: Giant Pages: 1

2015 BOXXER TEAM

Brand: SRAM Pages: 53

Brand: Abus Pages: 2

Roadmachine 2020

Brand: BMC Pages: 9

Urban Wireless+

Brand: Cateye Pages: 16

Brand: RBSM Pages: 34

Pedelec Groove*

Brand: Raleigh Pages: 397

Brand: Segway Pages: 17

Brand: APLIC Pages: 28

Brand: King-Meter Pages: 32

Brand: Mactronic Pages: 3

Brand: VDO Cyclecomputing Pages: 3

Brand: Wuxi LingDe Microelectronics Co., Ltd. Pages: 19

RACE ATTACK SL-160 CARBON

Brand: Rose electronics Pages: 2

Brand: Cateye Pages: 3

Brand: TAUBIK Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands