APRILIA RSV4 1100 Factory Service Station Manual Download Page 443 | Manualshive

Page: 443 / 549

background image

deflection must be constant throughout

the entire rotation of the wheel.

ADJUSTMENT

CAUTION

TO ADJUST THE CHAIN GET A SPECIFIC REAR SERVICE
STAND.

If you need to adjust the chain tension after the

check:

•

Place the vehicle on its rear service

stand.

•

Loosen the nut (1) completely.

•

Loosen the two lock nuts (4).

•

Use the adjuster screw (5) to adjust the

chain clearance checking that the ref-

erences (2-3) match on both sides of

the vehicle.

•

Tighten the two lock nuts (4).

•

Tighten the nut (1).

•

Check the chain clearance.

CAUTION

THERE ARE TWO FIXED REFERENCES (2-3) FOR WHEEL
CENTRING THAT CAN BE FOUND ON THE SWINGARM.

CHECKING WEAR OF CHAIN, PINION AND SPROCKET

Also regularly check the following parts and make sure that the chain, the pinion and the sprocket do

not show:

•

damaged rollers;

•

loosened pins;

•

dry, rusty, flattened or jammed chain links;

•

excessive wear;

•

missing sealing rings;

•

excessively worn or damaged pinion or sprocket teeth;

IF THE CHAIN ROLLERS ARE DAMAGED, THE PINS ARE LOOSE AND/OR THE SEAL RINGS
ARE DAMAGED OR MISSING, THE ENTIRE CHAIN UNIT (PINION, SPROCKET AND CHAIN)
NEEDS TO BE REPLACED.
LUBRICATE THE CHAIN REGULARLY, ESPECIALLY IF THERE ARE DRY OR RUSTY PARTS.
CRUSHED OR SEIZED LINKS MUST BE LUBRICATED AND RESTORED TO PROPER WORKING
ORDER.

THE DRIVE CHAIN HAS SEAL RINGS BETWEEN THE LINKS, WHICH KEEP THE GREASE INSIDE.

RSV4 1100 Factory

Chassis

CHAS - 443

«
...
441
442
443
444
445
...
»

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RSV4 1100 Factory

Brand: Kabuto Pages: 28

Brand: Duramaxx Pages: 44

iAero Generation III

Brand: iBike Pages: 40

Brand: KMART Pages: 2

Brand: wayscral Pages: 320

Brand: baby joy Pages: 11

Brand: SPIELWERK Pages: 11

303303/20190717TW012

Brand: APLIC Pages: 16

303508/20181218TW012

Brand: APLIC Pages: 32

Brand: Robstep Pages: 76

MXC Coil ext. Preload

Brand: Marzocchi Pages: 14

FEBER Baby Twist

Brand: Famosa Pages: 4

Brand: Cycle Torch Pages: 9

Brand: Rose electronics Pages: 4

Brand: allen Pages: 2

Brand: Topology Pages: 17

Brand: Crivit Pages: 22

Brand: Crivit Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands