APRILIA RSV4 1100 Factory Service Station Manual Download Page 118

Page: 118 / 549

WIRING TABLE D1 - ABS ON SADDLE MOUNT-

ING

The reference taping is purely indicative, position

the clamp so that it is aligned with the hole on the

saddle mounting. (the clamp may not be posi-

tioned above the taping)

Position the clamp without tightening it but allow-

ing it rotate of its own accord.

Insert the tip of the clamp into the hole on the sad-

dle mounting and push it until it locks into place.

1. Grey taping

2. Clamp

3. Saddle mounting hole

WIRING TABLE D2 - ABS ON SADDLE MOUNTING

IF THIS WIRING ABS FUSES-BATTERY) IS NOT SECURED CORRECTLY IT MAY CAUSE THE

VEHICLE TO CATCH FIRE

Check that the connected is securely attached and that all the terminals are in place. Position it as

indicated

1. ABS speed sensor connector

2. ABS positive wiring

3. ABS fuses

Electrical system

RSV4 1100 Factory

ELE SYS - 118

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands