APRILIA RSV4 1100 Factory Service Station Manual Download Page 189

Page: 189 / 549

•

Performed/Not performed

Indicates if the self-learning with the diagnostic tool was performed/not performed: if it was performed

one time, it will always remain performed unless a control unit EEPROM reset is carried out

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

CAUTION

IF ERRORS ARE DETECTED ON BOTH THROTTLE BODIES, CHECK ALSO THE CORRECT SUP-
PLY OF THE CONTROL UNIT TO PIN 42.

Rear bank throttle valve position potentiometer sensor P0120

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

Short-circuit to positive: excessive voltage has been detected on PIN 48. If open circuit, short

circuit to negative: voltage equal to zero detected at PIN 48

Troubleshooting

•

Short-circuit to positive: check the value shown by the parameter of the Rear throttle Po-

tentiometer 1 (voltage): disconnect the connector and read the value indicated in the

diagnostic tool: if the voltage does not vary, there is a short circuit of the cable, if the voltage

goes to zero, replace the throttle body

•

If open circuit, short circuit to negative: check the throttle body connector and the control

unit connector, if not ok restore, if everything is ok check the continuity of the circuit between

the two terminals, if not ok restore the wiring harness, if ok check the ground insulation of

the circuit (from the throttle valve sensor connector or control unit connector), if ground

insulated, check that the power supply (+5 V) is present at PIN 2 of the throttle body con-

nector and that ground is present at PIN 6, if present correctly replace the throttle body

Rear bank throttle valve position potentiometer sensor CF2 P2120

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

Short-circuit to positive: excessive voltage has been detected on PIN 50. If open circuit, short

circuit to negative: voltage equal to zero detected at PIN 50

Troubleshooting

•

Short-circuit to positive: check the value shown by the parameter of the Front throttle Po-

tentiometer 2 (voltage): disconnect the connector and read the value indicated in the

diagnostic tool: if the voltage does not vary, there is a short circuit of the cable, if the voltage

goes to zero, replace the throttle body

•

If open circuit, short circuit to negative: check the throttle body connector and the control

unit connector, if not ok restore, if everything is ok check the continuity of the circuit between

the two terminals, if not ok restore the wiring harness, if ok check the ground insulation of

the circuit (from the throttle valve sensor connector or control unit connector), if ground

RSV4 1100 Factory

Electrical system

ELE SYS - 189

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands