APRILIA RSV4 1100 Factory Service Station Manual Download Page 136

Page: 136 / 549

•

Fault in the switch (lock) of the engine start-up. A continuous voltage close to 0 was detected

for a certain time (e.g. locked button).

•

The instrument panel does not indicate the presence of this error even in the ATT status.

Troubleshooting

•

Check the locking cause and restore.

Fuses

AUXILIARY FUSES DISTRIBUTION

Specification

Desc./Quantity

A) 5A fuse

Stop and running lights relay

B) 10A fuse

Instrument panel, turn indicators, instrument panel diagnostics,

exhaust valve

C) 15A fuse

ECU

D) 7.5A fuse

ECU (2)

E) 15A fuse

High beam/low beam, horn.

F) 15A fuse

Coils, injectors, fuel pump, secondary air, injection relay

Auxiliary fuses are placed in the central part of the motorcycle, under the rider saddle.

ABS FUSE LAYOUT

Specification

Desc./Quantity

M) fuse of 15A

ABS solenoid valves.

N) fuse of 30A

ABS pump motor.

WHERE CONTEMPLATED

CAUTION

THREE OF THE FUSES ARE SPARES (H).

MAIN FUSES DISTRIBUTION

Specification

Desc./Quantity

H) 15A fuse

Fans

I) 30A fuse

Battery recharge, positive switched live, permanent positive

under instrument panel, sensor box positive switched live, fan

relay

Main fuses are placed in the rear part of the motorcycle, under the passenger seat.

Electrical system

RSV4 1100 Factory

ELE SYS - 136

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands