APRILIA RSV4 1100 Factory Service Station Manual Download Page 274

Page: 274 / 549

•

Screw a M10x120 screw in the secondary shaft hole, from the alternator side, to make it

easier to extract the gearbox unit.

•

Use a rubber mallet to tap on the sec-

ondary shaft from the alternator side to

detach the gearbox cover from the

crankcase.

•

Remove the complete gearbox unit.

Gearbox shafts

Disassembling the gearbox

Based on the design development of the engine, some gear components can have superficial treat-

ments of different types.

Some components of the gear can have a superficial cover in

WC/C

This coating consists of a layer composed of tungsten carbide lamellae alternating with amorphous

carbon lamellae. The coating

WC/C

has an elevated hardness and a good resistance to wear. The main

reason for using this coating is its extremely low friction coefficient, making this an ideal treatment for

preventing adhesion phenomena such as seizing and cold welding. The treatment has a characteristic

colouring, darker than at a traditional operation.

•

Only some components have the coat-

ing WC/C, among them:

1. Primary shaft

2. the gear of 3a-4a of the primary shaft;

3. All forks

Engine

RSV4 1100 Factory

ENG - 274

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands