APRILIA RSV4 1100 Factory Service Station Manual Download Page 390

Page: 390 / 549

Removing the injector

To optimise engine performance, there are four

lower injectors on the throttle bodies and four up-

per injectors on the filter box. Except during tran-

sition stages, only the lower or the upper injectors

are working at any given time.

•

The lower injectors optimise tractability

and reduce emissions and fuel con-

sumption

•

The upper injectors are designed for

maximum power output and, as a re-

sult, have a high fuel flow rate

The electrical connectors are colour coded as fol-

lows to prevent accidentally swapping the injector

connectors:

•

Cylinder 1: Black

•

Cylinder 2: Brown

•

Cylinder 3: Green

•

Cylinder 4: Grey

•

To remove the complete injectors unit,

disconnect and remove the engine

control unit complete with support

•

Undo the four screws fixing the injec-

tors unit to the filter box

•

Remove the complete injectors unit

from the filter box, disconnect the four

connectors of the injectors and remove

the complete injectors unit.

Power supply

RSV4 1100 Factory

P SUPP - 390

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands