APRILIA RSV4 1100 Factory Service Station Manual Download Page 196

Page: 196 / 549

•

Check the cleanliness of the throttle body and the intake duct. If ok replace the throttle body

Front throttle valve recovery conditions detection (Tair,Twater) P1409

•

Ice possibly present

Error cause

•

in conditions of low ambient temperature and engine temperature, a correct throttle valve

rotation was not detected: possible presence of ice in the duct (at each key ON). The in-

strument panel does not indicate the presence of this error even in the ATT status

Troubleshooting

•

Check the cleanliness of the throttle body and that there is no ice or condensate in the intake

duct. If ok replace the throttle body

Front throttle valve power supply voltage during self-learning P1410

•

Low power supply voltage

Error cause

•

The throttle valve power supply voltage is too low to correctly perform the self-learning test

(at each key ON). The instrument panel does not indicate the presence of this error even in

the ATT status

Troubleshooting

•

Remove the presence of errors that prevent throttle self-learning.

Front throttle valve position error - EPOS P0639 error

•

Misalignment between control and activation

Error cause

•

The throttle valve mechanical control could be damaged

Troubleshooting

•

Replace the throttle body

P1401 Rear throttle valve mechanical springs self-learning (opening)

Functional diagnosis:

•

Test failed

Error cause:

•

The recognition of this error is enabled during the throttle self-learning procedure.

•

Throttle valve return time, in the position maintained by the springs, outside of the specified

limits: the causes can be a deterioration of spring performance or excessive throttle valve

friction (at each key ON)

This error is indicated by lighting up in a fixed manner the MI warning light.

Troubleshooting:

Electrical system

RSV4 1100 Factory

ELE SYS - 196

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands