APRILIA RSV4 1100 Factory Service Station Manual Download Page 142

Page: 142 / 549

•

Circuit not functioning

Error cause:

•

Replace the injection control unit.

The instrument panel indicates this error by lighting up in a fixed manner the MI warning light.

NOTE

THIS ERROR GENERATES THE RECOVERY STATUS AND ENGINE SHUT-DOWN.

P0605 ROM Error

Electrical diagnosis:

•

Circuit not functioning

Error cause:

•

Replace the injection control unit.

The instrument panel indicates this error by lighting up in a fixed manner the MI warning light.

NOTE

THIS ERROR GENERATES THE RECOVERY STATUS AND ENGINE SHUT-DOWN.

P060B A/D converter

Electrical diagnosis:

•

Circuit not functioning

Error cause:

•

Replace the injection control unit.

The instrument panel indicates this error by lighting up in a fixed manner the MI warning light and by

flashing the general warning light.

NOTE

THIS ERROR GENERATES THE RECOVERY STATUS AND ENGINE SHUT-DOWN.

P1301 top lights relay error

Electrical diagnosis:

•

short circuit to positive / short circuit to negative / open circuit

Error cause:

•

Short-circuit to positive: excessive voltage has been detected on PIN 31.

•

If short circuit to negative: no voltage has been detected.

•

If open circuit: an interruption has been detected.

The instrument panel indicates this error by lighting up in a fixed manner the general warning light.

Troubleshooting

•

Short-circuit to positive: check the correct electrical characteristics of the relay by discon-

necting it from the wiring harness, if not ok replace the relay, if ok restore the wiring harness

(blue/pink cable)

Electrical system

RSV4 1100 Factory

ELE SYS - 142

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands