APRILIA RSV4 1100 Factory Service Station Manual Download Page 464

Page: 464 / 549

Guide to diagnosis

PREMISE

Each time the key is ON, if, at least one current or

stored* error is detected, the ABS warning light

turns on permanently.

The ABS system is deactivated automatically

The system operates perfectly just as any other

braking system without ABS

* The diagnosis requires exceeding the 5 km/h

(3.1 mph).

Each time the key is ON, if at least one current or stored* error of the ABS system is not detected:

•

the abs warning light flashes.

When the 5 km/h (3.1 mph) are exceeded:

- if errors are not detected: the ABS warning light turns off

- if at least one malfunction is detected: the ABS warning light turns on permanently.

The ABS system is disabled!

The system operates perfectly just as any other braking system without ABS.

The detection of malfunctions may require more or less time according to the type of failure.

Error detection logic foresees that for the errors to be diagnosed one or more conditions must persist

within a given time.

If during this given time one of the conditions is missing but then it comes back, the timer is reset and

the system is no longer able to diagnose the error.

The ABS system continues to be inactive.

GUIDE TO ABS FAULT DIAGNOSIS

1. ABS LAMP ON

2. CONNECT THE DIAGNOSTIC TOOL

DOES THE DIAGNOSTIC TOOL COMMUNICATE? (NO, go to 3; YES, go to 4)

3. PERFORM THESE CHECKS:

•

A. PIN 1 Ground connection

•

B. +12V at PIN 18

•

C. +12V live at PIN 4

ARE THERE ANY ERRORS? YES, go to point 5; NO, go to 6)

5. CHECK THE ERRORS TABLE

6. ABS WARNING LIGHT ACTIVATION

IS IT ACTIVATED?(YES, go to point 7; NO, go to point 8)

7. CONTACT TECHNICAL SERVICE

Braking system

RSV4 1100 Factory

BRAK SYS - 464

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands