APRILIA RSV4 1100 Factory Service Station Manual Download Page 76

Page: 76 / 549

Repeat the following operations:

•

move cylinder piston 1 (left rear piston)

to TDC;

•

turn the crankshaft 150° in the direction

of engine rotation (direction of travel) in

order to align the hole on the intake

camshaft with the specific hole on the

U bolt; this ensures that all the front

cylinder bank valve springs are decom-

pressed.

•

Refit the camshaft timing setting pin in

the hole in the U bolt on the front head,

and refit the crankshaft timing pin from

the flywheel side, to check that the tim-

ing setting was not altered while the

engine was turned with only one cam-

shaft drive gear fastener screw in

place.

•

Remove the camshaft timing pin.

•

Unscrew and remove the three screws

(1).

•

Remove the U bolt (2) and the oil pipe

(3).

Specific tooling

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

•

Block crankshaft rotation using one of

the specific tools.

•

Unscrew and remove the second in-

take camshaft gear screw.

•

Leave the gear on the camshaft.

Specific tooling

020850Y

Primary gear lock

020914Y

Flywheel stop

Maintenance

RSV4 1100 Factory

MAIN - 76

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands