APRILIA RSV4 1100 Factory Service Station Manual Download Page 322

Page: 322 / 549

•

rotate the crankshaft 150° in the engine rotation direction (direction of travel).

•

insert the respective pin, from the fly-

wheel side, into the groove on the

crankshaft.

NOTE

THE SPECIAL TOOL SHOWN HERE MUST ONLY BE USED
FOR IDENTIFYING THE CORRECT POSITION OF THE
CRANKSHAFT.
DO NOT USE IT FOR TIGHTENING COMPONENTS.

Specific tooling

020852Y

Crankshaft timing pin

NOTE

THIS ENGINE HAS CAMSHAFTS OF THE EXHAUST VALVES WITH CLEARANCE RECOVERY.

•

Install the intake and exhaust cam-

shafts on the front head, bearing in

mind that:

the exhaust camshaft gear tooth (indicated with a

dot) is meshed with the trough of the intake cam-

shaft gear (indicated with two dots).

CLEAN THOROUGHLY THE SEATS OF THE GEAR RE-
TAINER SCREWS, ON THE INTAKE CAMSHAFT.

•

Check the number engraved on the U

bolts, which must correspond with the

one engraved on the head.

•

If the U bolts between the two heads

are inverted, camshaft seizure may oc-

cur

IT IS NOT POSSIBLE TO REPLACE ONLY ONE U BOLT, IF
NECESSARY: REPLACE THE ENTIRE HEAD.

Engine

RSV4 1100 Factory

ENG - 322

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands