APRILIA RSV4 1100 Factory Service Station Manual Download Page 80

Page: 80 / 549

Specific tooling

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

•

Check if the clearance between the cam on the shaft and the tappet is correct.

•

If not, repeat the valve clearance adjustment procedure.

Rear cylinder head valves

•

Check the rear valve head clearance and restore the correct clearance values if necessary,

proceeding as described below.

•

Remove the rear head cover and the clutch cover.

•

Move cylinder piston 1 (left rear piston) to the TDC;

•

Turn the crankshaft 450° (one complete turn + 90°) in the direction of motor rotation (direction

of travel).

•

Insert the pin from the clutch side into

the hole in the crankshaft.

NOTE

THE SPECIAL TOOL SHOWN HERE MUST ONLY BE USED
FOR IDENTIFYING THE CORRECT POSITION OF THE
CRANKSHAFT.
DO NOT USE IT FOR TIGHTENING COMPONENTS.

Specific tooling

020852Y

Crankshaft timing pin

•

Fit the pin for aligning the intake cam-

shaft with the hole on U-bolt.

•

If it was not possible before adjusting

the valve clearance, check the engine

timing.

Specific tooling

020851Y

Camshaft timing pin

Maintenance

RSV4 1100 Factory

MAIN - 80

Summary of Contents for RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands

APRILIA RSV4 1100 Factory, Service Station Manual

Search results

Summary of Contents for RSV4 1100 Factory

Reviews:

Related manuals for RSV4 1100 Factory

Brands by name

Popular brands