Appear TV DC100 Series Product User Manual Download Page 78

Page: 78 / 352

APPEAR AS

Confidential

78/352

5.4.1.1

Setup of IPv6 input

The IP input module supports IPv6 multicast and unicast inputs. When using standard IPv6 address syntax

(128 bits, ‘:’ instead of ‘.’), the GUI will interpret the address as an IPv6 address.

The VLAN setup is independent on the choice of IPv4 or IPv6.
Source IP address has to match the IP format used for the destination IP address.

5.4.1.2

Source filtering on Switch IP input.

On the IP input, it is possible to use different mechanisms in order to filter on the Source IP address of the incoming
multicast.

Source filtering (relevant where 1 source is specified) is only available in IP input cards .

System behavior for different combinations of IGMP (version 2 or 3) input configurations:

Sources

Source filter

Comment

Off

GUI has not enabled filtering and no source is specified.

Only the multicast with the matching source address is available on the
input. This does not require IGMPv3

Off

In this mode all IGMPv3 sources are mapped to the same port. I.e. it is not
possible to reuse the MCAST:PORT pair on other inputs

Please note, only one of these sources should be active at a given time.

IGMPv3/SSM Source filtering is shown in figure below

Summary of Contents for DC100 Series

































































































































































































































































































































































Search results

Summary of Contents for DC100 Series

Reviews:

Related manuals for DC100 Series

Brands by name

Popular brands

Appear TV DC100 Series, Product User Manual

Search results

Summary of Contents for DC100 Series

Reviews:

Related manuals for DC100 Series

Brands by name

Popular brands