Appear TV DC100 Series Product User Manual Download Page 116 | Manualshive

Page: 116 / 352

background image

APPEAR AS

Confidential

116/352

CAM not identified, or
identified as non-CAM.

The PC Card is not identified, or identified as non-CAM.

When an error message is displayed, the

Back/Exit

button is replaced by

Refresh

. The operator can either

close the CAM Interface, or try to

Refresh

the session. If a synchronization error occurs,

Refresh

is the ideal

solution. Otherwise, the operator can wait for the CAM Interface to request a

Refresh

automatically.

6.2

G

ENERIC

D

ESCRAMBLER

CI

MODULE

(D

ESCRAMBLER GEN

.

2)

The Generic Descrambler CI module (Descrambler gen. 2) is a single slot processing card that supports 2 CAMs. The card
is hot-swappable with previous DDM-DCI module so rest all parameters are same as section 6.1.1 to 6.1.7

Each CAM has licenses to restrict use; "number-of-descrambled-services-cam-a" and "number-of-descrambled-services-
cam-b". The Descrambler supports both MUXing on the input and transparent mode, but each CAM can only be used for
one mode at a time. If services are being routed through a CAM in a mux-fashion, the CAM is unable to descramble other
services in transparent mode. MUXing supports descrambling in a single CAM services from any input source going to
any output source.

6.2.1.1

Configuration

Once the Generic Descrambler CI module is inserted with CAM in the chassis then outgoing services can be descrambled
by enabling it in the Descrambling tab, in the Edit Settings menu when editing an outgoing service.

The following parameters are available:

Descrambling

Slot and CI in which the Descrambler is installed either Sx:A or Sx:B

Descrambled Services

Select the services which needs to be descrambled using that CAM

«
...
114
115
116
117
118
...
»

Summary of Contents for DC100 Series

































































































































































































































































































































































Reviews:

No comments

Related manuals for DC100 Series

Brand: Zenith Pages: 54

Brand: Zenith Pages: 2

Brand: Datavideo Pages: 35

Brand: A2Z Ozone Systems Pages: 13

Brand: A2Z Ozone Pages: 17

Brand: 3onedata Pages: 3

Brand: D&H Pages: 70

Brand: Streetwize Pages: 12

Brand: Sima Pages: 2

Brand: Baum Pages: 32

Brand: Baja Silueta Pages: 99

Brand: Delta Electronics Pages: 2

CONSONANCE REFERENCE DB1

Brand: Opera Pages: 3

INTERNATIONAL TRAVEL ADAPTER

Brand: Igo Pages: 1

Brand: WATANABE Pages: 2

Brand: SHENZHEN ENCOM ELECTRIC TECHNOLOGIES CO. Pages: 30

Brand: Fronius Pages: 92

Brand: BZBGEAR Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands