Appear TV DC100 Series Product User Manual Download Page 64 | Manualshive

Page: 64 / 352

background image

APPEAR AS

Confidential

64/352

Module

License

Description

audio-
encoder/trans
coder

number-of-mpeg1-and-
aac-stereo-encoders

Enables the MPEG1L2 or AAC Encoding for a number of stereo pairs.

number-of-auto-
loudness-adjustment-
instances

Enables Automatic Loudness adjustments feature on audio

Supports up to 32 stereos in total

scrambler

number-of-scrambled-
services

Enables the number of services to be scrambled and the corresponding encryption
algorithm.

aes-cbc-irdeto

Vendor specific scrambling license.

pvr-pes-clear

Enables PVR PES Clear mode for the scrambler and ensures that the pes headers are not
scrambled.

rai-pvr-mode

Enabled Conax PVR Assist (RAI) mode

tvmod

modulation-analog

Enables PAL or Secam modulation for the output.

num-channels

Enables 4 or 8 channels to be output.

cabletv-in

dvbc-input

Enables 16 channels to be input

J83b-input

Enables j83b standard

If a licensed feature is used without the correct license installed, the system will produce a

License Violation

warning. Use the

License

node to find which licenses are acquired and available.

4.4.1

O

RDERING A

L

ICENSE

F

ILE

Use the License node to order a license file. Flag the required licenses using the check boxes. The

Order License

button will produce a license order file which should be sent to the vendor. A matching license file will then be
returned.

4.4.2

I

NSTALLING A

L

ICENSE

F

ILE

A valid license file may contain licenses for one or several cards. This means that one license file may be used for
several units. The installation process will scan the file and if a matching serial number is found the license will be
installed on the respective card within the unit. The license file is signed; if edited, it will be invalid.

Usually, the license file will be sent in a ZIP file and can be loaded directly to the GUI.

Once a license file is available from a machine with access to the web GUI, select the file and click

Install License

.

If no warnings are displayed, the additional privileges should now be available.

«
...
62
63
64
65
66
...
»

Summary of Contents for DC100 Series

































































































































































































































































































































































Reviews:

No comments

Related manuals for DC100 Series

Brand: JED Pages: 4

Brand: Camoga Pages: 43

Brand: Perlight Solar Pages: 19

VENUS X8K LEGENDARY

Brand: RGBlink Pages: 33

Brand: Lika Pages: 2

Brand: Gbxpoint Pages: 4

ALL-USB-RS422/485

Brand: Allnet Pages: 6

Brand: GMI Pages: 9

EQUINOX EQX2 4002-HT

Brand: Salicru Pages: 108

Media Giant CM3G Series

Brand: Conceptronic Pages: 2

Brand: Lambda Pages: 47

BLANKOM SDE-1265

Brand: Irenis Pages: 22

basic-line DCC 1-00

Brand: axing Pages: 4

Brand: Linear Pages: 3

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

Brand: Teac Pages: 18

ControlMaster Edge

Brand: R&M Pages: 2

Brand: Weco Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands