Appear TV DC100 Series Product User Manual Download Page 61

Page: 61 / 352

APPEAR AS

Confidential

61/352

Module

License

Description

dab

modulation-dab

Enables DAB modulation for the output.

num-ts

Enables the number of maximum possible output multiplexes.

dvb-t2

dvbt2-input

Enables the DVB-T2 demodulation options.

srt

srt-input

Enables srtSRT input

srt

Srt- output

Enables srtSRT output options.

isdbtout-cable

modulation-cofdm

Enables COFDM modulation for the output.

num-ts

Enables the number of maximum possible output multiplexes.

dvbs-if

dvbs-lband

modulation-dvbs2

Enables DVB-S2 modulation for the output.

num-ts

Enables the number of maximum possible output multiplexes.

precorrection

Enables precorrection on output stream

dvbs2x-in

dvbs2

Enables the DVB-S2 demodulation options

dvbs2-input-multistream

Enables Multistream reception option for the DVB-S2 module

dvbs2x-input

Enables the DVB-S2X input

dvbs2-input-blindscan

Enables blindscan option

number-of-t2plp-
extractions

Enables the de-encapsulation of a total of 64 PLPs from up to 64 T2MI input streams per
input card

dvbs2x-out

carrier-id

Enables Carrier ID option

modulation-dvbs2

Enables DVB-S2 modulation for the output.

modulation-dvbs2x-bc

Enables S2X MODCODS up to and including 64-APSK ,all roll-offs and normal FEC size

modulation-dvbs2x-pro

Enables S2X MODCODS up to and including 64-APSK,all roll-offs and short FEC size

num-ts

Enables the number of maximum possible output multiplexes.

precorrection

Enables precorrection on output stream

s2x-10mhz-ref

Enables embedded 10MHz output option

encoder

number-of-hd-encoders

Enables the number of HD services to be encoded.

number-of-sd-encoders

Enables the number of SD services to be encoded.

number-of-statmux-
channels

Number of channels with Statistical multiplexing enabled

transcoder

number-of-hd-encoders

Enables the number of HD services to be transcoded.

number-of-sd-encoders

Enables the number of SD services to be transcoded.

number-of-statmux-
channels

Number of channels with Statistical multiplexing enabled

Summary of Contents for DC100 Series

































































































































































































































































































































































Search results

Summary of Contents for DC100 Series

Reviews:

Related manuals for DC100 Series

Brands by name

Popular brands

Appear TV DC100 Series, Product User Manual

Search results

Summary of Contents for DC100 Series

Reviews:

Related manuals for DC100 Series

Brands by name

Popular brands